欢迎光临深圳市益烽达电子有限公司!

 服务热线 :136-0307-4319(周先生)

产品banner
您当前的位置 : 首 页 > 龙岗UVLED面光源
龙岗UVLED面光源

龙岗UVLED面光源

  • 所属分类:龙岗UVLED面光源
  • 浏览次数:
  • 发布日期:2021-06-02 09:54:38
  • 产品概述

                                                              YFD300100-F                   


                                     UV lamp parameters

名称nameUVLED面光源UVLED surface light source
芯片chip韩国LG芯片Seoul chip功率power700W
光功率Optical power1000-3000mwcm2波长wavelength365nm
输入input40V、4.2A功率power0-100%
辐射面Radiation surface300X100mm散热dissipate heat风冷Air cooling
环境温度ambient temperature-10℃~50℃芯片寿命Chip life20000H


                                                  实拍UV灯头图

  产品特点 Product features

1)无需预热,即开即用;

     No preheating, ready to use
2)不含汞,既安全又环保

     Mercury free, safe and environmentally friendly
3) 产品功率小,节能省电

     Product power is small, energy saving
4 设备结构简洁大方,轻便,易集成

    The equipment structure is simple, light and easy to integrate
5冷光源,无热辐射,降低了固化过程产生的热量

    Cold light source, no thermal radiation, reduce the heat generated during the curing process
6 采用精密的光学分析技术,光效率密度高,均匀性高达90%以上

    Using precise optical analysis technology, the optical efficiency density is high, and the uniformity is more than 90%
7采用韩国LG垂直结构LED紫外灯珠,寿命长达20000小时以上

    It adopts Korean LG vertical structure led UV lamp bead, with a service life of more than 20000 hours.

   参数设置Parameter setting


开机画面Boot screen

    

按下Welcome”按钮画面如下Press the "welcome" button, and the screen is as follows  

           

 

能量值:UV灯功率0-100%(Energy value: UV lamp power 0-100%)

自动模式:按下启动UV灯亮倒计时开始,时间到灯灭。

Automatic mode: press start UV light, countdown start, time to light out.)

手动模式:按下启动UV灯亮,按下停止UV等灭。

Manual mode: press to start UV light on, press to stop UV light off.)

倒计时:时间设定大于0时才会显示

Countdown: only when the time setting is greater than 0)

温度:显示铜基板上的温度

Temperature: displays the temperature on the copper substrate

启动:按下灯亮 Start: press the light to light up)

停止:按下灯灭 Stop: press the light to go out)

灯亮时按钮指示灯亮、灭时指示灯灭

When the light is on, the button indicator light is on, and when it is off, the indicator light is off)

   温度超温报警时UV灯不亮

      参数设置界面Parameter setting interface

   


照射时间:设置为自动模式时时间计时有效

Irradiation time: the time is valid when it is set to automatic mode

运行时间:UV灯累计时间

Running time: UV lamp cumulative time

报警温度:设定报警时温度,设置范围0-100℃

Alarm temperature: set the alarm temperature, setting range 0-100 ℃

                       

        电箱端子接线图


UVLED be careful when using the product


Whether the fan port is covered by other objects


Lamp cap: when using UV LED lamp cap, it is recommended to clean the glass surface of lamp cap with alcohol once a week, and use air gun or vacuum cleaner to remove excessive dust and garbage inside the controller and on the grid.


Electric box: once a month on a regular basis, use air gun or vacuum cleaner equipment to remove the dust on the fan of the electric box, so as to prevent excessive dust for a long time from reducing the heat dissipation of the electric box and reducing the service life of the electric box.


Note: before maintenance, be sure to cut off the power supply, pull out the power cord, and after maintenance, the equipment can be used only after it is completely dry to prevent danger.


标签

上一篇:水冷面光源2021-06-02
下一篇:uv无影胶固化灯2022-11-12

近期浏览:

相关产品

相关新闻